How to Fix Skewing Roman Shades & Crooked Window Blinds

White roman shade above a kitchen sink in a blue kitchenImage by Another Human

Every custom roman shade from The White Window arrives fully assembled, with all its hardware, ready to put up. But our shades travel a long way from the workroom to your window, and now and then a setting shifts on the journey, so a shade hangs crooked or folds unevenly once it’s up. If yours is skewing, don’t worry: it’s a quick fix, with no tools and no need to take the shade down.

Here’s how to fix roman shades (and crooked window blinds) that skew or hang unevenly, in a few minutes. First, a quick look at the lift lines behind the shade and what makes a shade skew; then, step by step, how to find the line lock that has slipped and set it back in place.

Understanding How Roman Shades Operate


Lift lines running down the back of a roman shade

A critical part of any roman shade’s anatomy is its ‘lift lines’ - vertical cords that run from top to bottom, on the backside of the shade. A shade of up to about 50 in wide will typically have three lift lines; a wider shade may have more. 

 

 

If your roman shade is skewing/hanging crooked when operated, one (or more) of the line locks has likely moved out of its position - while in transit or during installation - leading to unequal length/ tension between the lines.

How to Fix Roman Shades: Adjusting the Lift Lines

Now, the solution. Let’s explain it step by step -

  • Lower your shade to fully unfold. Then stand on the rear side of the shade so you are in a position to see the mechanism behind your shade. 
  • Maneuver the pull cord until the shade folds up to its first fold/slat from the bottom. When the bottom bar touches the preceding slat, pause. (Refer to the video below for visual assistance). This is the moment of diagnosis where you can pinpoint the error with just a little bit of observation.



 
  • Observe the position of the lift lines as well as the ‘line locks’ at the bottom. All line locks should ideally rest on the loop ring of the bottom-most slat at the exact same level. But, you may notice that one (or more) of the locks has slid out of its place either up or down on the lift line. The goal is to bring the line locks back to their position so that all the lines are standing at the same length and tension levels. 
  • Now, hold the line lock between your fingers and look for the toggle button. (Refer to the video in the previous section.) Press the button and maneuver it up or down until it reaches its designated position - the loop ring of the last slat, while being completely level with other line locks. 
  • If the lock has been displaced below the last slat, draw it upward until it rests on the loop ring of the last slat. Then, release your finger. If, on the other hand, the lock has moved above the last slat, draw it downward. 
  • When the lock has rested on the loop ring of the last slat, level with other locks, and release the finger. Now it is locked and will not move out of its position. When the last lift line is fixed and the line lock fastened, your roman shade will have assumed its correct position. The job’s done!

And that’s how you make a skewed roman shade straight!

Fixing Roman Shades: FAQs

What is a line lock on a roman shade?

A small clip on each lift line that rests on the loop ring of the bottom slat and holds the line at a set length. If one slips up or down, in transit or while the shade is being put up, that side folds higher or lower than the rest and the shade skews.

How do you fix a roman shade that won’t fold evenly?

Lower it fully, raise it until the bottom bar meets the first slat, then look at the back: the line locks should sit level on the bottom slat’s loop rings. Slide any that have moved back into line.

What are the lift lines on a roman shade?

The cords that run down the back of the shade from the headrail to the bottom slat. When you pull the cord, they lift the slats one by one, folding the fabric as it rises.

How many lift lines does a roman shade have?

A shade up to about 50 in wide usually has three; wider shades may have more.

Do you need tools to fix a skewing roman shade?

No. Each line lock has a toggle button: press it with your fingers, slide the lock along the lift line, then let go and it locks in place.

What if the shade is still uneven after adjusting the line locks?

Check that the brackets are level and the channel track is clicked fully into each one. If it still skews, email us at hi@thewhitewindowshades.com with a photo of the back of the shade and we’ll help.

How do you keep a roman shade from skewing again?

Raise and lower it with the pull cord in a smooth, steady movement, and keep the cord anchor fitted so the cord stays taut. Once the line locks are set level, they stay put.

Still Need a Hand?

Most skewing shades are straight again in a couple of minutes. If yours isn’t, or you’re not sure which line lock has moved, email us at hi@thewhitewindowshades.com with a photo or a short video of the back of the shade, and we’ll help you put it right.

WINDOW WISDOM: HOW TO FIT ROMAN SHADES: INSTALLATION GUIDE | INSIDE MOUNT VS. OUTSIDE MOUNT ROMAN SHADES

Back to blog